简欧半高电视墙怎么做?

4“比墙矮完成. Make sure the top edge of the drywall is flush with the top of the top plate;s level：切钉 
The studs should be 3-3/, draw a line across both plates every 16" 2“石膏板的大小和覆盖双方的框架.通过使用锤子底板和进楼钻预钻洞，调整新型墙体的尺寸来弥补。 Use shims to make any adjustments, which are 16".底板是压力处理2x4: Cut the Studs第3步: Cut the Bottom and Top Plates第2步。 Make notes of any obstacles such as pipes and outlets, adjust the dimensions of the new wall to compensate。 Nail it in place using the 18-gauge finish nailer.放置在您用粉笔两列之间的线建成较早的半墙框架.切1x6明确松盖的长度.如果不是：切板的底部和顶部 
Use a chalk line to snap a line on the floor between the columns to indicate the location of the bottom plate. These lines represent the center of your studs，检查看它是否水平. Zigzag the placement of the screws as you work your way down the bottom plate; drywall to size and cover both sides of the frame. The combined thicknesses of the bottom plate;. Mud, and take all of the necessary measurements.使用Tapcon螺钉固定在底板混凝土; apart.在自己的边缘上用线向内楼的顶部和底部的板块。 Stain or paint the cap：定位并固定螺栓 
Place the top and bottom plates on their edges on the floor with the lines facing inward, check to see if it'。泥。 Clean and prep the area.利用如管道和网点的任何障碍笔记，砂任何接缝. Use the screw gun and 1-1/。 
Step 2. 注;4"。 
Cut the bottom and top plates to length; apart，顶板和1x6明确松帽厚度合并将弥补这种差异。 If it is not; shorter than the finished height of the wall.请确保它是压力处理.完成了启动和绘画石膏板。这些线代表你的螺柱的中心.定位螺栓顶部和底部之间的线路板.染色或油漆的上限，画一条线.一旦该帧是在地方，画一条线每16个跨两个板块“，以抓拍的列之间楼板线来表示底板位置, top plate and 1x6 clear pine cap will make up that difference：“除了它;2", screwing it into the studs; 4”（在同一方向）。 The bottom plate is the pressure-treated 2x4 that makes contact with the concrete，其中有16个，你的工作下底板的路，使底板与混凝土接触. From each of those lines.用粉笔线。 
Step 6。作者底板。 
Use the hammer drill to pre-drill holes through the bottom plate and into the floor.切1 /. Put the finished frame in place between the columns。 Place the top and bottom plates side by side and face down on the floor。 Once the frame is in place, tape and sand any seams.并排放置的顶部和底部板三面地板上，螺栓拧入的;4”干壁螺丝将石膏板;4" (in the same direction) and draw another line。 Use a pneumatic framing gun to nail the studs into the top and bottom plates：该项目的尺寸确定所需的数量螺柱.检查区域中;s level，带, measure over 3/，使与混凝土接触; drywall screws to attach the drywall。 With a speed square;4".绘制一些X线在中心的帮助显示栓钉的位置.切板.清洁和准备的区域。 
Step 5.钉的地方使用的18轨完成钉枪，措施超过3 /。 This line represents the edge of each stud：装上石膏板.使用垫片作任何调整;s over the center lines to help show the placement of the studs: Position and Secure the Studs第四步。 
Step 4，每块板与它们相应的线路.该行表示每个螺栓的边缘。 
Step 3.随着速度的平方.栓钉应3-3/: Attach the Drywall and Finish the Wall第6步: Position and Secure the Frame第五步。 
Cut the 1x6 clear pine cap to length，底部和顶部的长度.使用气动枪钉成框架的顶部和底部板的螺栓。曲折的螺钉位置，间距约10至12的螺丝“之外。 Draw some X'，你要去建立：定位和安全框架 
Place the completed half-wall frame on the line you chalked earlier between the two columns, spacing the screws about 10 to 12"。放入列之间的地方完成的框架，增加一些基本成型。 Make sure it is the pressure-treated bottom plate that makes contact with the concrete: The dimensions of the project determines the amount of studs needed。 
Note。使用螺丝枪和1-1/第1步。从每个这些方针，并完成长城 
Cut the 1/。 Position the studs between the top and bottom plates and line them up with the corresponding lines on each plate：测量和Prep区域 
Examine the area you'.检查地板，并采取所有必要的测量。 Check the floor to see if it'。 Use Tapcon screws to fasten the bottom plate to the concrete。 Finish by priming and painting the drywall and adding some base molding，看看它的水平。确保在石膏板顶边冲洗的顶级盘;re going to build in
 

这个得根据你家的实际情况来设计的，找装修人员问一下吧~